MG 15 BASS
Subwoofer Mobile Group
MG 15 Bass is the mobile assembly designed for the MM 15 UNLIMITED car audio subwoofers ; it is the ideal solution for those who look for a deep, undistorted bass. The innovative RMA (Removable Moving Assembly) provides the ability to replace the entire mobile assembly in few seconds, without removing the speaker from its mounting position. MG 15 Bass features a 60 mm long excursion aluminium voice coil wound on a four-layer KSV former as well as a Double Symmetrical Spider system and a motor design optimized to increase thermal and mechanical capability. The water repellent pressed paper cone is enclosed by high density foam surrounds, to ensure maximum linearity even at high excursions.
Data table
Size mm (in.) | 380 (15) |
Power Handling - Peak W | 8000 |
Power Handling - Continuous W | 2000 |
Impedance Ω | 1 + 1 |
Frequency response Hz | 28 ÷ 700 |
Voice coil Ø mm (in.) | 75 (3) |
Cone/Dome | Water-repellent, pressed paper |
Xmax mm | 20 |
X-mech mm (in.) | 35 (1.4) |
Re Ω | 2,3 |
Fs Hz | 30 |
Vas l | 81,9 |
Qts | 0,5 |
Qes | 0,55 |
Qms | 5,55 |
Spl dB | 94 |
MM 15.1 UNLIMITED
Subwoofer Motor Group
MM 12.1 UNLIMITED and MM 15.1 UNLIMITED car audio subwoofers are exclusively designed for SPL competitions. In order to achieve the best performance on each individual race circuit, the SPL Monster subwoofers offer the ability to choose the moving assembly which is most appropriate for the overall system design, achieving maximum SPL in every competition. MM 15.1 UNLIMITED is a 15 in. (380 mm) motor group. In order to ensure constant, even flux, it features high magnetic permeability plates. The oversized magnet provides perfect control even under very high excursion conditions. Basket and motor are coupled and damped through a special epoxy glue.
Data table
Size mm (in.) | 380 (15) |
Magnet | Double magnet, High density flux ferrite |
Magnet size D x d x h mm (in.) | 2 x 230 x 25 (2 x 9.1 x 1) |
MG 15 BASS
Subwoofer Mobile Group
MG 15 Bass is the mobile assembly designed for the MM 15 UNLIMITED car audio subwoofers ; it is the ideal solution for those who look for a deep, undistorted bass. The innovative RMA (Removable Moving Assembly) provides the ability to replace the entire mobile assembly in few seconds, without removing the speaker from its mounting position. MG 15 Bass features a 60 mm long excursion aluminium voice coil wound on a four-layer KSV former as well as a Double Symmetrical Spider system and a motor design optimized to increase thermal and mechanical capability. The water repellent pressed paper cone is enclosed by high density foam surrounds, to ensure maximum linearity even at high excursions.
Data table
Size mm (in.) | 380 (15) |
Power Handling - Peak W | 8000 |
Power Handling - Continuous W | 2000 |
Impedance Ω | 1 + 1 |
Frequency response Hz | 28 ÷ 700 |
Voice coil Ø mm (in.) | 75 (3) |
Cone/Dome | Water-repellent, pressed paper |
Xmax mm | 20 |
X-mech mm (in.) | 35 (1.4) |
Re Ω | 2,3 |
Fs Hz | 30 |
Vas l | 81,9 |
Qts | 0,5 |
Qes | 0,55 |
Qms | 5,55 |
Spl dB | 94 |
MM 15.1 UNLIMITED
Subwoofer Motor Group
MM 12.1 UNLIMITED and MM 15.1 UNLIMITED car audio subwoofers are exclusively designed for SPL competitions. In order to achieve the best performance on each individual race circuit, the SPL Monster subwoofers offer the ability to choose the moving assembly which is most appropriate for the overall system design, achieving maximum SPL in every competition. MM 15.1 UNLIMITED is a 15 in. (380 mm) motor group. In order to ensure constant, even flux, it features high magnetic permeability plates. The oversized magnet provides perfect control even under very high excursion conditions. Basket and motor are coupled and damped through a special epoxy glue.
Data table
Size mm (in.) | 380 (15) |
Magnet | Double magnet, High density flux ferrite |
Magnet size D x d x h mm (in.) | 2 x 230 x 25 (2 x 9.1 x 1) |
HP 6001
D-CLASS MONO AMPLIFIER WITH CROSSOVER
HP 6001 is the most powerful spl car audio amplifier within the SPL Show line. The overbuilt power supply stage and the D Class output stage featuring 12 Mosfets provide the ability to deliver up to 6000W power.
The wide array of possible setups, with by-passable Lo-Pass filter (24 dB/Oct. slope), subsonic filter, phase control and remote volume control, make HP 6001 an extremely powerful amplifier, perfect for SPL applications.
Thanks to the Chain Mode function, to cascade a second amplifier into a single load, a devastating amount of power up to 12000W can be achieved with record SPL levels.
Accessories
HRC
Sub Volume Remote Control
Sub Volume Remote Control (HRC) allows the user to adjust subwoofer level from dashboard.
Data table
Channel mode | 1 |
Output Power (RMS) @ 14.4 VDC |
1 Ch: 1670 W x 1 (4 Ω) 1 Ch: 2970 W x 1 (2 Ω) 1 Ch: 5000 W x 1 (1 Ω) |
Filters Lo-Pass |
50 ÷ 400 Hz @ 24 dB/Oct. |
Distortion - THD (100Hz @ 4Ω) |
0.1 % |
S/N Ratio (A weighted @ 1V) |
86 dB |
Damping factor (100Hz @ 4Ω) |
500 |
Size W x D x H mm (in.) |
644 x 280 x 65,5 (25.35 x 11.02 x 2.55) |
Technologies
-
OVERBUILT POWER SUPPLY STAGE
In order to deliver such extraordinarily high power and to transfer it uninterruptedly, the power supply stage features multiple toroidal transformers, 105° Low ESR primary capacitors, TO247 Mosfets and large tank-type secondary capacitors. -
CIRCUIT BOARDS AND COMPONENT DESIGNED SPECIFICALLY FOR SPL SYSTEMS
Inside the amplifier, the electronics have been designed specifically for SPL systems, driving low impedance loads with perfect thermal stability. Power for sound pressure without compromise. -
ULTRA-VERSATILE AND COMPLETE CONTROL AND FILTER SYSTEM
The Front End section features a complete crossover system, for endless configuration possibilities. HP 3001/HP 6001 mono models are provided with by-passable Lo-Pass filter (24 dB/Oct. slope), subsonic filter, phase control, remote volume control (HRC) and also a Chain Mode function to cascade-connect a second amplifier, achieving maximum SPL levels. -
ALUMINIUM EXTRUDED HEATSINK WITH MASSIVE FINS FOR UNPARALLELED THERMAL STABILITY
Aluminium extruded heatsink with enhanced thermal performance. Following the style of Hertz, the Hertz logo has been tastefully integrated into the top of the HP heatsink, and massive fins are featured along the side of the amplifier.
MG 15 BASS
Subwoofer Mobile Group
MG 15 Bass is the mobile assembly designed for the MM 15 UNLIMITED car audio subwoofers ; it is the ideal solution for those who look for a deep, undistorted bass. The innovative RMA (Removable Moving Assembly) provides the ability to replace the entire mobile assembly in few seconds, without removing the speaker from its mounting position. MG 15 Bass features a 60 mm long excursion aluminium voice coil wound on a four-layer KSV former as well as a Double Symmetrical Spider system and a motor design optimized to increase thermal and mechanical capability. The water repellent pressed paper cone is enclosed by high density foam surrounds, to ensure maximum linearity even at high excursions.
Data table
Size mm (in.) | 380 (15) |
Power Handling - Peak W | 8000 |
Power Handling - Continuous W | 2000 |
Impedance Ω | 1 + 1 |
Frequency response Hz | 28 ÷ 700 |
Voice coil Ø mm (in.) | 75 (3) |
Cone/Dome | Water-repellent, pressed paper |
Xmax mm | 20 |
X-mech mm (in.) | 35 (1.4) |
Re Ω | 2,3 |
Fs Hz | 30 |
Vas l | 81,9 |
Qts | 0,5 |
Qes | 0,55 |
Qms | 5,55 |
Spl dB | 94 |
MM 15.1 UNLIMITED
Subwoofer Motor Group
MM 12.1 UNLIMITED and MM 15.1 UNLIMITED car audio subwoofers are exclusively designed for SPL competitions. In order to achieve the best performance on each individual race circuit, the SPL Monster subwoofers offer the ability to choose the moving assembly which is most appropriate for the overall system design, achieving maximum SPL in every competition. MM 15.1 UNLIMITED is a 15 in. (380 mm) motor group. In order to ensure constant, even flux, it features high magnetic permeability plates. The oversized magnet provides perfect control even under very high excursion conditions. Basket and motor are coupled and damped through a special epoxy glue.
Data table
Size mm (in.) | 380 (15) |
Magnet | Double magnet, High density flux ferrite |
Magnet size D x d x h mm (in.) | 2 x 230 x 25 (2 x 9.1 x 1) |
MP 15K UNLIMITED
D-CLASS SPL AMPLIFIER
The Hertz MP 15K UNLIMITED spl car audio amplifier can deliver over 15.000 W. The enormity of this project amazes; both in terms of the physical “size” of the product itself and of the sheer energy it generates.
The power supply stage features 8 toroidal transformers and the output stage, settable in bridged or stereo mode, features 20 -190A/360V impulsive current Mosfets: solid, robust power and thermal dissipation without compromise.
Direct Current® , the power supply connection system, transfers power between the battery and amplifier with very low contact resistance, to achieve the current transfer required for high SPL systems.
The Hertz SPL Stack System® provides the ability to stack multiple MP 15K UNLIMITED amplifiers, using 6 robust iron Brackets. With the Hertz SPL Stack System® your system can deliver 15.000 W, 30.000 W, 45.000 W, or more, just stack and connect!
Accessories
Brackets included
Data table
Channel mode | 2-1 |
Output Power (RMS) @ 14.4 VDC |
Load Impedance Stereo Bridge 4Ω 1500 W x 2 5600 W x 1 2Ω 2800 W x 2 9000 W x 1 1Ω 4500 W x 2 12000 W x 1 |
Filters Lo-Pass |
OFF / Lo-pass: 40 ÷ 150 Hz @ 24 dB/Oct. |
Distortion - THD (100Hz @ 4Ω) |
0.15 % |
S/N Ratio (A weighted @ 1V) |
69 dB |
Damping factor (100Hz @ 4Ω) |
> 950 |
Size W x D x H mm (in.) |
323 x 830 x 68,5 (12.8 x 32.7 x 2.8) |
Press review
-
MP15K unlimited
2009-02-12
Technologies
-
DIRECT CURRENT®
4 x 1/0 AWG cables secured to the amplifier through 4 x 2,5 mm thick copper buss bars connected directly to the printed circuit board, to transfer power between battery and amplifier with very low contact resistance. -
HERTZ SPL STACK SYSTEM®
Hertz SPL Stack System® stacks multiple amplifiers thanks to the 6 supplied 2 mm robust iron brackets mounted on the threaded points on the heatsink.
MP 15K UNLIMITED
D-CLASS SPL AMPLIFIER
The Hertz MP 15K UNLIMITED spl car audio amplifier can deliver over 15.000 W. The enormity of this project amazes; both in terms of the physical “size” of the product itself and of the sheer energy it generates.
The power supply stage features 8 toroidal transformers and the output stage, settable in bridged or stereo mode, features 20 -190A/360V impulsive current Mosfets: solid, robust power and thermal dissipation without compromise.
Direct Current® , the power supply connection system, transfers power between the battery and amplifier with very low contact resistance, to achieve the current transfer required for high SPL systems.
The Hertz SPL Stack System® provides the ability to stack multiple MP 15K UNLIMITED amplifiers, using 6 robust iron Brackets. With the Hertz SPL Stack System® your system can deliver 15.000 W, 30.000 W, 45.000 W, or more, just stack and connect!
Accessories
Brackets included
Data table
Channel mode | 2-1 |
Output Power (RMS) @ 14.4 VDC |
Load Impedance Stereo Bridge 4Ω 1500 W x 2 5600 W x 1 2Ω 2800 W x 2 9000 W x 1 1Ω 4500 W x 2 12000 W x 1 |
Filters Lo-Pass |
OFF / Lo-pass: 40 ÷ 150 Hz @ 24 dB/Oct. |
Distortion - THD (100Hz @ 4Ω) |
0.15 % |
S/N Ratio (A weighted @ 1V) |
69 dB |
Damping factor (100Hz @ 4Ω) |
> 950 |
Size W x D x H mm (in.) |
323 x 830 x 68,5 (12.8 x 32.7 x 2.8) |
Press review
-
MP15K unlimited
2009-02-12
Technologies
-
DIRECT CURRENT®
4 x 1/0 AWG cables secured to the amplifier through 4 x 2,5 mm thick copper buss bars connected directly to the printed circuit board, to transfer power between battery and amplifier with very low contact resistance. -
HERTZ SPL STACK SYSTEM®
Hertz SPL Stack System® stacks multiple amplifiers thanks to the 6 supplied 2 mm robust iron brackets mounted on the threaded points on the heatsink. -
MG 15 BASS
Subwoofer Mobile Group
MG 15 Bass is the mobile assembly designed for the MM 15 UNLIMITED car audio subwoofers ; it is the ideal solution for those who look for a deep, undistorted bass. The innovative RMA (Removable Moving Assembly) provides the ability to replace the entire mobile assembly in few seconds, without removing the speaker from its mounting position. MG 15 Bass features a 60 mm long excursion aluminium voice coil wound on a four-layer KSV former as well as a Double Symmetrical Spider system and a motor design optimized to increase thermal and mechanical capability. The water repellent pressed paper cone is enclosed by high density foam surrounds, to ensure maximum linearity even at high excursions.
Data table
Size mm (in.) 380 (15) Power Handling - Peak W 8000 Power Handling - Continuous W 2000 Impedance Ω 1 + 1 Frequency response Hz 28 ÷ 700 Voice coil Ø mm (in.) 75 (3) Cone/Dome Water-repellent, pressed paper Xmax mm 20 X-mech mm (in.) 35 (1.4) Re Ω 2,3 Fs Hz 30 Vas l 81,9 Qts 0,5 Qes 0,55 Qms 5,55 Spl dB 94 MM 15.1 UNLIMITED
Subwoofer Motor Group
MM 12.1 UNLIMITED and MM 15.1 UNLIMITED car audio subwoofers are exclusively designed for SPL competitions. In order to achieve the best performance on each individual race circuit, the SPL Monster subwoofers offer the ability to choose the moving assembly which is most appropriate for the overall system design, achieving maximum SPL in every competition. MM 15.1 UNLIMITED is a 15 in. (380 mm) motor group. In order to ensure constant, even flux, it features high magnetic permeability plates. The oversized magnet provides perfect control even under very high excursion conditions. Basket and motor are coupled and damped through a special epoxy glue.
Data table
Size mm (in.) 380 (15) Magnet Double magnet, High density flux ferrite Magnet size D x d x h mm (in.) 2 x 230 x 25 (2 x 9.1 x 1)
HP 802
STEREO AMPLIFIER WITH CROSSOVER
HP 802 is an AB Class stereo spl car audio amplifier, able to deliver up to 1800W. The power supply stage is overbuilt featuring components selected for their robustness, efficiency and reliability even for extended time operation. The output stage features an oversized power supply with 4 toroidal transformers, providing the ability to deliver remarkable power and work stable into 1 Ohm load.
The array of the featured filters is remarkably complex, beyond the standards of mobile electronics in this category: separate Hi-Pass and Lo-Pass filters, able to be configured into a 50 Hz – 10 Hz adjustable Band-Pass filter. A parametric equalizer is also on board, to optimize the response on amplified channels, as well as a Pre Out, to re-launch the input signal to another HP 802 in a multi-amplified system without limits on the number of ways.
Data table
Channel mode | 2-1 |
Output Power (RMS) @ 14.4 VDC |
2 Ch: 330 W x 2 (4 Ω) 2 Ch: 550 W x 2 (2 Ω) 2 Ch: 800 W x 2 (1 Ω) 1 Ch: 1100 W x 1 (4 Ω) 1 Ch: 1600 W x 1 (2 Ω) |
Filters Hi-Pass Lo-Pass Band-Pass |
50 ÷ 1k Hz / 500 ÷ 10k Hz 50 ÷ 1k Hz / 500 ÷ 10k Hz 50 ÷ 10k Hz (HI) 50 ÷ 10k Hz (LO) |
Distortion - THD (100Hz @ 4Ω) |
0.05 % |
S/N Ratio (A weighted @ 1V) |
103 dB |
Damping factor (100Hz @ 4Ω) |
500 |
Size W x D x H mm (in.) |
544 x 240 x 65,5 (21.41 x 9.45 x 2.55) |
Press review
Technologies
-
OVERBUILT SUPPLY STAGE
In order to deliver such extraordinarily high power and to transfer it uninterruptedly, the power supply stage features multiple toroidal transformers, 105° Low ESR primary capacitors, TO247 Mosfets and large tank-type secondary capacitors. -
CIRCUIT BOARDS AND COMPONENT DESIGNED SPECIFICALLY FOR SPL SYSTEMS
Inside the amplifier, the electronics have been designed specifically for SPL systems, driving low impedance loads with perfect thermal stability. Power for sound pressure without compromise. -
ULTRA-VERSATILE AND COMPLETE CONTROL AND FILTER SYSTEM
The Front End section features a complete crossover system, for endless configuration possibilities. HP 802 is a stereo amplifier with separate Hi-Pass and Lo-Pass filters, operable in combination to create a Band-Pass filter; it also features an adjustable parametric equalizer as well as a Pre Out to re-launch the signal to other amplifiers in a multi-amplified system. -
ALUMINIUM EXTRUDED HEATSINK
Aluminium extruded heatsink with enhanced thermal performance. Following the style of Hertz, the Hertz logo has been tastefully integrated into the top of the HP heatsink, and massive fins are featured along the side of the amplifier.