HP 6001
D-CLASS MONO AMPLIFIER WITH CROSSOVER
HP 6001 is the most powerful spl car audio amplifier within the SPL Show line. The overbuilt power supply stage and the D Class output stage featuring 12 Mosfets provide the ability to deliver up to 6000W power.
The wide array of possible setups, with by-passable Lo-Pass filter (24 dB/Oct. slope), subsonic filter, phase control and remote volume control, make HP 6001 an extremely powerful amplifier, perfect for SPL applications.
Thanks to the Chain Mode function, to cascade a second amplifier into a single load, a devastating amount of power up to 12000W can be achieved with record SPL levels.
Accessories
HRC
Sub Volume Remote Control
Sub Volume Remote Control (HRC) allows the user to adjust subwoofer level from dashboard.
Data table
Channel mode | 1 |
Output Power (RMS) @ 14.4 VDC |
1 Ch: 1670 W x 1 (4 Ω) 1 Ch: 2970 W x 1 (2 Ω) 1 Ch: 5000 W x 1 (1 Ω) |
Filters Lo-Pass |
50 ÷ 400 Hz @ 24 dB/Oct. |
Distortion - THD (100Hz @ 4Ω) |
0.1 % |
S/N Ratio (A weighted @ 1V) |
86 dB |
Damping factor (100Hz @ 4Ω) |
500 |
Size W x D x H mm (in.) |
644 x 280 x 65,5 (25.35 x 11.02 x 2.55) |
Technologies
-
OVERBUILT POWER SUPPLY STAGE
In order to deliver such extraordinarily high power and to transfer it uninterruptedly, the power supply stage features multiple toroidal transformers, 105° Low ESR primary capacitors, TO247 Mosfets and large tank-type secondary capacitors. -
CIRCUIT BOARDS AND COMPONENT DESIGNED SPECIFICALLY FOR SPL SYSTEMS
Inside the amplifier, the electronics have been designed specifically for SPL systems, driving low impedance loads with perfect thermal stability. Power for sound pressure without compromise. -
ULTRA-VERSATILE AND COMPLETE CONTROL AND FILTER SYSTEM
The Front End section features a complete crossover system, for endless configuration possibilities. HP 3001/HP 6001 mono models are provided with by-passable Lo-Pass filter (24 dB/Oct. slope), subsonic filter, phase control, remote volume control (HRC) and also a Chain Mode function to cascade-connect a second amplifier, achieving maximum SPL levels. -
ALUMINIUM EXTRUDED HEATSINK WITH MASSIVE FINS FOR UNPARALLELED THERMAL STABILITY
Aluminium extruded heatsink with enhanced thermal performance. Following the style of Hertz, the Hertz logo has been tastefully integrated into the top of the HP heatsink, and massive fins are featured along the side of the amplifier.
MG 15 BASS
Subwoofer Mobile Group
MG 15 Bass is the mobile assembly designed for the MM 15 UNLIMITED car audio subwoofers ; it is the ideal solution for those who look for a deep, undistorted bass. The innovative RMA (Removable Moving Assembly) provides the ability to replace the entire mobile assembly in few seconds, without removing the speaker from its mounting position. MG 15 Bass features a 60 mm long excursion aluminium voice coil wound on a four-layer KSV former as well as a Double Symmetrical Spider system and a motor design optimized to increase thermal and mechanical capability. The water repellent pressed paper cone is enclosed by high density foam surrounds, to ensure maximum linearity even at high excursions.
Data table
Size mm (in.) | 380 (15) |
Power Handling - Peak W | 8000 |
Power Handling - Continuous W | 2000 |
Impedance Ω | 1 + 1 |
Frequency response Hz | 28 ÷ 700 |
Voice coil Ø mm (in.) | 75 (3) |
Cone/Dome | Water-repellent, pressed paper |
Xmax mm | 20 |
X-mech mm (in.) | 35 (1.4) |
Re Ω | 2,3 |
Fs Hz | 30 |
Vas l | 81,9 |
Qts | 0,5 |
Qes | 0,55 |
Qms | 5,55 |
Spl dB | 94 |
MM 15.1 UNLIMITED
Subwoofer Motor Group
MM 12.1 UNLIMITED and MM 15.1 UNLIMITED car audio subwoofers are exclusively designed for SPL competitions. In order to achieve the best performance on each individual race circuit, the SPL Monster subwoofers offer the ability to choose the moving assembly which is most appropriate for the overall system design, achieving maximum SPL in every competition. MM 15.1 UNLIMITED is a 15 in. (380 mm) motor group. In order to ensure constant, even flux, it features high magnetic permeability plates. The oversized magnet provides perfect control even under very high excursion conditions. Basket and motor are coupled and damped through a special epoxy glue.
Data table
Size mm (in.) | 380 (15) |
Magnet | Double magnet, High density flux ferrite |
Magnet size D x d x h mm (in.) | 2 x 230 x 25 (2 x 9.1 x 1) |